Five Piece
Mitered Drawers
Drawer Front images are also shown above most of the door designs shown on this website.

Go to the bottom of this page for Product Offerings and Availabilities. Below each photograph are listed the Drawer Front Design, the minimum sizes, and panel information.The line drawing below each photograph shows a cross-section of the drawer front.
CRP 10 Miter DF
Min.: 7 1/2" w x 7 1/2"h
2 5/16" Framing
Slant Raise Shown
CRP 10191 DF
Min.: 3 7/8" w x 3 7/8"h
1 1/2" Framing
P-057 Raise Shown
CRP 10318 DF
Min.: 4 3/8" w x 4 3/8"h
1 3/4" Framing
P-057 Raise Shown
CRP 10334 DF
Min.: 4 7/8" w x 4 7/8"h
2" Framing
P-057 Raise Shown
CRP 10382 DF
Min.: 5 1/2" w x 5 1/2"h
2 5/16" Framing
P-057 Raise Shown
CRP 10533 DF
Min.: 5 1/2" w x 5 1/2"h
2 5/16" Framing
P-057 Raise Shown
CRP 10605 DF
Min.: 5 3/8" w x 5 3/8"h
2 1/16" Framing
Chamfer Raise Shown
CRP 10751 DF
Min.: 5 1/2" w x 5 1/2"h
2 5/16" Framing
P-057 Raise Shown
CRP 10827 DF
Min.: 5 1/2" w x 5 1/2"h
2 5/16" Framing
P-057 Raise Shown
CRP 10875 DF
Min.: 4 7/8" w x 4 7/8"h
2" Framing
P-057 Raise Shown
CRP 10946 DF
Min.: 4 1/8" w x 4 1/8"h
1 5/8" Framing
P-057 Raise Shown
CRP 1389 DF
Min.: 6 7/8" w x 6 7/8"h
2" Framing
Slant Raise Shown
CRP 1420 DF
Min.: 4 7/8" w x 4 7/8"h
2" Framing
P-057 Raise Shown
Milan DF
Min.: 5" w x 5"h
2" Framing
P-057 Raise Shown
Mirage DF
Min.: 5 1/2" w x 5 1/2"h
2 5/16" Framing
P-057 Raise Shown
Presidental Miter DF
Min.: 5 7/8" w x 5 7/8"h
2 1/2" Framing
P-057 Raise Shown
Prestige DF
Min.: 4 7/8" w x 4 7/8"h
2" Framing
P-057 Raise Shown
TW 10522 DF
Min.: 5 1/4" w x 5 1/4"h
2 5/16" Framing
9/16" Veneered Panel
Product Offering and Availabilities:
  • Special Note:
    Drawer Fronts have horizontal grain panel standard.
    Vertical grain available upon request.
    Minimums listed are based on raises shown.
    Minimums will vary depending on panel raise selection.
  • Wood Species:
    All 3/4" species available except quarter sawn and rustic knotty.
    All 1" species available in CRP 10 Miter except quarter sawn and rustic knotty.
    Exception - TW10522 not available in Alder, Mahogany, Soft Maple, White Oak, quarter sawn or rustic knotty species.
  • Edge Profiles:
    CRP 10191, CRP 10334, CRP 10827, CRP 10875, CRP 10-0946, CRP 101420, Milan, and Prestige - no choices available.
    CRP 10318 standard as shown, C-2, LC-2, PRS-2 also available.
    TW 10522 - all 3/4" profiles available.
    All others - all available.
  • Framing Beads:
    All available for CRP 10 Miter.
    All others - no choices available.
  • Panel Raises:
    CRP 10605 - chamfer, Rev. G-Cove, and P-075 only.
    Prestige - all 3/4" raises available.
    TW 10522 - 9/16" veneered panel.
    All others - all 3/4" raises available.
    CRP 10 Miter - all 3/4" and 1" raises available.
  • Options:
    All drawers can receive back routed hand pull, G-012, G-056, G-121 routs, distressing, wear sanding, and V-Groove.
    CRP 10 Miter, CRP 382, CRP 10533, CRP 10605, CRP 10571, CRP 1389, Mirage, Presidential Miter, and TW 10522 can receive face routed hand pull.
  • Appliance Panels:
    Apply over plywood - all available.
    CRP 10 Miter, CRP 10382, CRP 10533, CRP 10605, CRP 10571, CRP 1389, Mirage, and Presidential Miter - glue-in strips available.
    Prestige - apply over plywood only.
    TW 10522 - apply over plywood or glue-in strips available.